Labelmate

Abra a página inicial da InterMédia Informática (www.intermedia.pt) InterMédia Informática
Tel. 239703577 ou 917808746 Fax 239703577 info@intermedia.pt compras@intermedia.pt

Tabela actualizada em 09/11/2018
Labelmate - enroladores e dispensadores de etiquetas               € s/IVA € c/IVA
Quando indicada uma "Quantidade mínima sugerida" o preço refere-se ao total dessa quantidade, pode vender-se só 1, mas em quantidade é mais barato, para outras quantidades consulte-nos           _______    
Enroladores de etiquetas Ref.         Quant. mín. sugerida Valor p/ a  quantidade
REENROULEUR AJUST. 25-101mm DIAM PRNT (ver também LMR005) CAT-3-ACH info pdf pdf ver  1 unid. = 492,00 605,16
REENROULEUR STD + BRAS TENSION PRNT CAT-3-TA-STD  1 unid. = 548,00 674,04
RRC-330-STANDARD Handles labels up to 152mm wide. Roll capacity up to 330mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 235cm/sec. LMC001 info pdf pdf ver  1 unid. = 988,00 1215,24
RRC-330-ACH Handles labels up to 152mm wide. Roll capacity up to 330mm. Available for 38, 40, 44, 70, 76 and 100mm cores for the unwind shaft. Adjustable core holder (25 to 101mm) for the take-up shaft. Speed up to 235cm/sec. LMC002 info pdf pdf ver  1 unid. = 1114,00 1370,22
RRC-330-U-STANDARD Handles labels up to 152mm wide. Roll capacity up to 330mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 235cm/sec. LMC003 info pdf pdf ver  1 unid. = 1522,00 1872,06
RRC-330-U-ACH Handles labels up to 152mm wide. Roll capacity up to 330mm. Available for 38, 40, 44, 70, 76 and 100mm cores for the unwind shaft. Adjustable core holder (25 to 101mm) for the take-up shaft. Speed up to 235cm/sec. LMC004 info pdf pdf ver  1 unid. = 1684,00 2071,32
COUNT-100 Pre-set Counter, handles labels up to 170mm label width. LMC005 info pdf pdf ver  1 unid. = 429,00 527,67
COUNT-200 Pre-set Counter, handles labels up to 255mm label width. LMC006 info pdf pdf ver  1 unid. = 520,00 639,60
LD-100-RS distribuidor automático de etiquetas impressas, largura de etiqueta até 115mm, comprimento de 6 a 150mm (dependendo das etiquetas, avança automaticamente para disponibilizar a próxima etiqueta a retirar, não adequado a etiquetas transparentes. Handles labels up to 115mm wide. Roll diameter capacity 220mm. Label length from 6 to 150mm. Min speed 11cm/sec. LMD001 info pdf pdf ver  1 unid. = 398,00 489,54
LD-100-RS + 210x200x270mm ACCS + C-1 COUNTER OPTION  LMD001+LMX445  1 unid. = 473,00 581,79
LD-200-RS Handles labels up to 165mm wide. Roll diameter capacity 220mm. Label length from 6 to 150mm. Min speed 11cm/sec. LMD002 info pdf pdf ver  1 unid. = 416,00 511,68
LD-200-RS POWER LABEL DISP CPNT LD-AWB ADJ WEARLESS BRAKE  LMD002/LMX447  1 unid. = 528,00 649,44
LD-200-RS 270x200x270mm ACCS + C-1 COUNTER OPTION  LMD002+LMX445  1 unid. = 509,00 626,07
LD-100-RS-SS Handles labels up to 115mm wide. Roll diameter capacity 220mm. Label length from 6 to 150mm. Min speed 11cm/sec. LMD003 info pdf pdf ver  1 unid. = 458,00 563,34
LD-100-RS-SS + 210x200xX270mm ACCS + C-1 COUNTER OPTION  LMD003+LMX445  1 unid. = 554,00 681,42
LD-200-RS-SS Handles labels up to 165mm wide. Roll diameter capacity 220mm. Label length from 6 to 150mm. Min speed 11cm/sec. LMD004 info pdf pdf ver  1 unid. = 493,00 606,39
LD-200-RS-SS + 270x200x270mm ACCS + C-1 COUNTER OPTION  LMD004+LMX445  1 unid. = 589,00 724,47
LD-100-U Handles labels up to 115mm wide. Roll diameter capacity 220mm. Label length from 10 to 150mm for regular labels. Label length from 20 to 150mm for transparent labels. Min speed 11cm/sec. LMD005 info pdf pdf ver  1 unid. = 432,00 531,36
LD-200-U Handles labels up to 165mm wide. Roll diameter capacity 220mm. Label length from 10 to 150mm for regular labels. Label length from 20 to 150mm for transparent labels. Min speed 11cm/sec. LMD006 info pdf pdf ver  1 unid. = 477,00 586,71
LD-200-U-SS Handles labels up to 165mm wide. Roll diameter capacity 220mm. Label length from 10 to 150mm for regular labels. Label length from 20 to 150mm for transparent labels. Min speed 11cm/sec. LMD008 info pdf pdf ver  1 unid. = 557,00 685,11
P-300-LS REEL-TO-REEL Label PRNT ACCS INKJ LOW SP HIGH RES LMP001  1 unid. = 3210,00 3948,30
P-300-HS REEL-TO-REEL Label PRNT ACCS INKJ HIGH SP LOW RES  LMP002  1 unid. = 3210,00 3948,30
PM-300-LS Handles labels up to 125mm width. 300mm roll diameter capacity. Low Speed Model (150cm/Sec). REEL-TO-REEL Label PRNT ACCS 800X380X330mm LMP003 info pdf pdf ver  1 unid. = 1458,00 1793,34
PM-300-HS Handles labels up to 125mm width. 300mm roll diameter capacity. High Speed Version (235cm/sec). REEL-TO-REEL Label PRNT ACCS 800x380x330mm LMP004 info pdf pdf ver  1 unid. = 1522,00 1872,06
PM-300-CS For applications requiring constant speed. Handles label up to 125mm width. 300mm diameter roll capacity. Speed up to 40 or 60cm/sec. Is a constant reel-to-reel label printer Mechanism for inkjet and laser heads. Ideal for applications requiring constant speed (eg. for RFID encoding). This unit works at constant adjustable speed, independently of the supply and rewind roll diameters. The maximum speed is 40cm/sec  or 61cm/sec depending on the request. (Long term speed stability 5%), is an ideal table top platform for OEM applications that use an ink-jet head. When not used as a printer, the PM-300 can be used a reel-to-reel counter/Rewinder. LMP005 info pdf pdf ver  1 unid. = 1917,00 2357,91
MC-10 Handles labels up to 125mm wide. Roll diameter capacity up to 220mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 50cm/sec. Handles labels up to 125 mm wide and will wind a roll of labels up to a 220 mm diameter. The new build-in potentiometer allows to control the amount of rewind speed/torque. No awkward, troublesome belts or clutches are used and no speed adjustments are required. The Mini-Cat has an inner label flange to keep the edge of the label web aligned as the labels are being rewound. LMR001 info pdf pdf ver  1 unid. = 278,00 341,94
MC-10-1-INCH Handles labels up to 125mm wide. Roll diameter capacity up to 220mm. Available for 38, 40, 44, 70, 76 and 100mm cores, for 25.4mm core, handles labels up to 125 mm wide and will wind a roll of labels up to a 220 mm diameter. The new build-in potentiometer allows to control the amount of rewind speed/torque. No awkward, troublesome belts or clutches are used and no speed adjustments are required. The Mini-Cat has an inner label flange to keep the edge of the label web aligned as the labels are being rewound. For 24.5mm cores. Speed up to 50cm/sec. Rewinder Unwinder CPNT 220x350x195mm. LMR002 info pdf pdf ver  1 unid. = 278,00 341,94
MC-11 Handles labels up to 115mm wide. Roll diameter capacity up to 220mm. Adjustable core holder from 25 to 101mm. Speed up to 50cm/sec. Handles labels up to 115 mm wide and will wind a roll of labels up to a 220 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm.The new build-in potentiometer allows to control the amount of rewind speed/torque. No awkward, troublesome belts or clutches are used and no speed adjustments are required. he Mini-Cat has an inner label flange to keep the edge of the label web aligned as the labels are being rewound. LMR003 info pdf pdf ver  1 unid. = 291,00 357,93
CAT-3-STANDARD Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. Hlabels up to 155 mm wide and will wind a roll of labels up to a 300 mm diameter. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. 300x350x320mm LMR004 info pdf pdf ver  1 unid. = 453,00 557,19
CAT-3-ACH Handles labels up to 155mm wide. Roll diameter capacity up to 280mm. Adjustable core holder from 25 to 101mm. Speed up to 125cm/sec. Handles labels up to 155 mm wide and will wind a roll of labels up to a 280 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR005 info pdf pdf ver  1 unid. = 482,00 592,86
CAT-3-CHUCK Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR006 info pdf pdf ver  1 unid. = 588,00 723,24
CAT-3-10-INCHES Handles labels up to 255mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. LMR007 info pdf ver  1 unid. = 500,00 615,00
CAT-3-1-INCH Handles labels up to 155mm wide. Roll diameter capacity up to 220mm. For 24.5mm cores. Speed up to 125cm/sec. Handles labels up to 155mm wide and will wind a roll of labels up to a 220 mm diameter. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR008 info pdf pdf ver  1 unid. = 453,00 557,19
CAT-3-TASTANDARD (Tension Arm Version) Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. The CAT-3-STANDARD handles labels up to 155 mm wide and will wind a roll of labels up to a 300 mm diameter. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR010 info pdf  1 unid. = 549,00 675,27
CAT-3-TA-ACH (Tension Arm version) Handles labels up to 155mm wide. Roll diameter capacity up to 280mm. Adjustable core holder from 25 to 101mm. Speed up to 125cm/sec. The CAT-3-ACH handles labels up to 155 mm wide and will wind a roll of labels up to a 280 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR011 info pdf  1 unid. = 615,00 756,45
CAT-3-TA-CHUCK (Tension Arm version) Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR012 info pdf  1 unid. = 669,00 822,87
CAT-3-TA-10-INCHES (Tension Arm version) Handles labels up to 255mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. Handles labels up to 255mm (10-inches) wide and will wind a roll of labels up to a 300 mm diameter. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-3 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR013 info pdf ver  1 unid. = 584,00 718,32
CAT-40G-TA (Tension Arm Version) Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 400mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 38cm/sec. The CAT-40G is gear motor driven for more torque. It accepts bigger rolls with a diameter up to 400mm. The CAT-40G handles labels up to 170, 220 or 270mm wide. This model is equipped with durable “Quick-Chuck” quick-locking Core Chuck, permitting the fastest loading and unloading of cores and label rolls. Standard Quick-Chuck: Core diameter: 76mm – Label width: 170mm. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-40G Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. LMR015 info pdf ver  1 unid. = 914,00 1124,22
TWIN-CAT-2 (BASE UNIT) (without any core holder) Your choice of core holders. Handles labels up to 270mm wide. Roll diameter capacity up to 220mm. Speed up to 125cm/sec. The Twin-CAT-2 is a fast and easy way to deliver label rolls the way you want them. With two motors and your choice of core holders, you have maximum versatility in setting up the operation you need. Both spindles can rewind, unwind and be controlled (direction and torque) independently. Many possible applications: Inside wound to outside wound; Reverse the order of serialized labels; Rewind labels on a different core size; Wind small rolls of labels from larger ones; Strip matrix from die-cut labels inline with your printer; Rewind a specific quantity of labels with the inspection and pre-set counter options. Size: W x D x H: 180 x 370 x 470 mm. LMR016 info pdf pdf ver  1 unid. = 641,00 788,43
CAT-4-STANDARD Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. The CAT-4-STANDARD handles labels up to 155 mm wide and will wind a roll of labels up to a 300 mm diameter.  An external commande interface on the CAT-4 allows to support direct control start/stop by the barcode printer (check compatibility with your printer vendor). The CAT-4 offers also an optional adjustable Start Delay to allow the printer to execute back-feed withtout resistance from the rewinder. Rugged, heavy-gauge steel construction allows your CAT-4 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 350 x 320 mm. LMR025 info pdf pdf ver  1 unid. = 467,00 574,41
CAT-4-ACH Handles labels up to 155mm wide. Roll diameter capacity up to 280mm. Adjustable core holder from 25 to 101mm. Speed up to 125cm/sec. The CAT-4-ACH handles labels up to 155 mm wide and will wind a roll of labels up to a 280 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm. An external commande interface on the CAT-4 allows to support direct control start/stop by the barcode printer (check compatibility with your printer vendor). The CAT-4 offers also an optional adjustable Start Delay to allow the printer to execute back-feed withtout resistance from the rewinder. Rugged, heavy-gauge steel construction allows your CAT-4 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 280 x 310 x 365 mm. LMR026 info pdf pdf ver  1 unid. = 496,00 610,08
CAT-4-CHUCK Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 280mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec.The CAT-4-CHUCK handles labels up to 170, 220 or 270mm wide and will wind a roll of labels up to a 300 mm diameter. This model includes durable “Quick-Chuck” quick-locking Core Chuck, permitting the fastest loading and unloading of cores and label rolls. Standard Quick-Chuck: Core diameter: 76mm / Label width: 170mm. To find other Quick-Chuck dimensions click here. Torque and Direction are fully controllable from the Control Panel. Dual torque ranges provide plenty of power for use with a LABELMATE Slitter, too. Rugged, heavy-gauge steel construction allows your CAT-4 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 385 x 320 mm. LMR027 info pdf pdf ver  1 unid. = 602,00 740,46
CAT-4-10-INCHES Handles labels up to 255mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. The CAT-4-10-INCHES handles labels up to 255mm (10-inches) wide and will wind a roll of labels up to a 300 mm diameter. An external commande interface on the CAT-4 allows to support direct control start/stop by the barcode printer (check compatibility with your printer vendor). The CAT-4 offers also an optional adjustable Start Delay to allow the printer to execute back-feed withtout resistance from the rewinder. Rugged, heavy-gauge steel construction allows your CAT-4 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 455 x 320 mm. LMR028 info pdf pdf ver  1 unid. = 515,00 633,45
CAT-4-1-INCH Handles labels up to 155mm wide. Roll diameter capacity up to 220mm. For 24.5mm cores. Speed up to 125cm/sec. The CAT-4-1-INCH, for 25.4mm cores, handles labels up to 155mm wide and will wind a roll of labels up to a 220 mm diameter. An external commande interface on the CAT-4 allows to support direct control start/stop by the barcode printer (check compatibility with your printer vendor). The CAT-4 offers also an optional adjustable Start Delay to allow the printer to execute back-feed withtout resistance from the rewinder. Rugged, heavy-gauge steel construction allows your CAT-4 Rewinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 220 x 350 x 280 mm LMR029 info pdf pdf ver  1 unid. = 457,00 562,11
MC-10+ With External Control. Handles labels up to 125mm wide. Roll diameter capacity up to 220mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 50cm/sec. The MC-10+ handles labels up to 125 mm wide and will wind a roll of labels up to a 220 mm diameter. The new build-in potentiometer allows to control the amount of rewind speed/torque. No awkward, troublesome belts or clutches are used and no speed adjustments are required. The MC+ is complete and reliable thanks to its external control. It enables the printer to control the rewinder, activating it only when printing or feeding forward. The Mini-Cat has an inner label flange to keep the edge of the label web aligned as the labels are being rewound. LMR030 info pdf ver  1 unid. = 332,00 408,36
MC-11+ RHandles labels up to 115mm wide. Roll diameter capacity up to 220mm. Adjustable core holder from 25 to 101mm. Speed up to 50cm/sec. The MC-11+ handles labels up to 115 mm wide and will wind a roll of labels up to a 220 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm. The new build-in potentiometer allows to control the amount of rewind speed/torque. No awkward, troublesome belts or clutches are used and no speed adjustments are required. The Mini-Cat has an inner label flange to keep the edge of the label web aligned as the labels are being rewound. The MC-11+ is complete and reliable thanks to its external control. It enables the printer to control the rewinder, activating it only when printing or feeding forward. 220X305X195mm. LMR032 info pdf ver  1 unid. = 348,00 428,04
S-100 Handles labels up to 170mm width. 2 high-precision blades. Optional Pre-set Counter Available. Same speed as the printer or the rewinder. The rugged S-100 Slitter allows you to slit down multiple-across label rolls to the desire width. It can be used either “in-line”, between the printer and the label rewinder, or “off-line”, between an unwinder and a rewinder. S-100 Slitter has two high-precision, break-away blades for clean, even slitting of material. The S-100 requires a CAT-3 Rewinder (CAT-3-CHUCK is recommended.). Size: W x D x H: 355 x 280 x 250 mm.  LMS001 info pdf pdf ver  1 unid. = 317,00 389,91
S-200 Handles labels up to 255mm width. 3 high-precision blades. Optional Pre-set Counter Available. Same speed as the printer or the rewinder. The rugged S-200 Slitter allows you to slit down multiple-across label rolls to the desire width. It can be used either “in-line”, between the printer and the label rewinder, or “off-line”, between an unwinder and a rewinder. S-200 Slitter has three high-precision, break-away blades for clean, even slitting of material. The S-200 requires a CAT-3 Rewinder (CAT-3-CHUCK-10” is recommended.).. Size: W x D x H: 435 x 280 x 250 mm. LMS002 info pdf pdf ver  1 unid. = 392,00 482,16
S-100-SP Self-powered Slitter Unit 60VA CPNT 90-250VAC 50-60Hz. Size: W x D x H: 355 x 280 x 250 mm.  LMS003 pdf  1 unid. = 654,00 804,42
UCAT-S Non-Powered Unwinder. Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Same speed as the printer. Unpowered label unwinder with adjustable wearless brake. The UCAT-S accepts up to 300mm diameters rolls and up to 155mm width, 76mm core holder as standard. Rugged, heavy-gauge steel construction allows your UCAT-S Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 365 x 320 mm. LMU001 info pdf ver  1 unid. = 173,00 212,79
UCAT-S EC LBL UNWINDER 76MM STDACCS +R-16 OPTION UCAT-1-STD INSTALL  LMU001/LMX457  1 unid. = 237,00 291,51
UCAT-S EC LBL UNWINDER 40MM ACCS AD BRAKE 300x365x320mm LMU001-40MM  1 unid. = 173,00 212,79
UCAT-1-STANDARD Self-powered Unwinder. Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Same speed as the printer. The Classic Labelmate self-powered Unwinder with Adjustable Speed-Proportional Braking. The UCAT-1-STANDARD accepts up to 300mm diameters rolls and up to 155mm width, 76mm core holder as standard. Rugged, heavy-gauge steel construction allows your UCAT-1-STANDARD Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 350 x 320 mm. LMU002 info pdf pdf ver  1 unid. = 368,00 452,64
UCAT-1-ACH Self-powered Unwinder. Handles labels up to 155mm wide. Roll diameter capacity up to 280mm. Adjustable core holder from 25 to 101mm. Sames speed as the printer. The Classic Labelmate self-powered Unwinder with Adjustable Speed-Proportional Braking. The UCAT-1-ACH handles labels up to 155 mm wide and will unwind a roll of labels up to a 280 mm diameter. This unit includes an Ajustable Core Holder (ACH) that accepts any core size from 25mm to 101mm. Rugged, heavy-gauge steel construction allows your UCAT-1-ACH Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving.. Size: W x D x H: 300 x 350 x 320 mm. LMU003 info pdf pdf ver  1 unid. = 399,00 490,77
UCAT-1-CHUCK Self-powered Unwinder. Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Sames speed as the printer. The Classic Labelmate self-powered Unwinder with Adjustable Speed-Proportional Braking. The UCAT-1-CHUCK handles labels up to 170, 220 or 270mm wide and will unwind a roll of labels up to a 300 mm diameter. This model includes durable “Quick-Chuck” quick-locking Core Chuck, permitting the fastest loading and unloading of cores and label rolls. Standard Quick-Chuck: Core diameter: 76mm / Label width: 170mm. Rugged, heavy-gauge steel construction allows your UCAT-1-CHUCK Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 385 x 320 mm LMU004 info pdf pdf ver  1 unid. = 498,00 612,54
UCAT-1-10-INCHES Self-powered Unwinder. Handles labels up to 255mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Same speed as the printer. The Classic Labelmate self-powered Unwinder with Adjustable Speed-Proportional Braking. The UCAT-1-10-INCHES handles labels up to 255mm (10-inches) wide and will unwind a roll of labels up to a 300 mm diameter. Rugged, heavy-gauge steel construction allows your UCAT-1-10-INCHES Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving. Size: W x D x H: 300 x 455 x 320 mm. LMU005 info pdf pdf ver  1 unid. = 408,00 501,84
UCAT-3-STD Handles labels up to 155mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. This powered Unwinder, with Tension Arm, automatically tracks label usage and provides powered label feed at speeds up to 125 cm/sec. The UCAT-3 accepts standard 76 mm cores and rolls up to 300 mm in diameter. LABELMATE’s renowned Constant Adjustable Torque control system allows precise adjustment of feed speeds and rewind torque. External STOP / RUN Input included. LMU007 info pdf ver  1 unid. = 530,00 651,90
UCAT-3-ACH Handles labels up to 155mm wide. Roll diameter capacity up to 280mm. Adjustable core holder from 25 to 101mm. Speed up to 125cm/sec. This powered Unwinder, with Tension Arm, automatically tracks label usage and provides powered label feed at speeds up to 125 cm/sec. The UCAT-3-ACH includes an Adjustable Core Holder (ACH) that accepts any core size from 25mm to 101mm in diameter and up to 155mm in width. LABELMATE’s renowned Constant Adjustable Torque control system allows precise adjustment of feed speeds and rewind torque. External STOP / RUN Input included. 300x350xX320mm. LMU008 info pdf ver  1 unid. = 581,00 714,63
UCAT-3-CHUCK Handles labels up to 270mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. This powered Unwinder, with Tension Arm, automatically tracks label usage and provides powered label feed at speeds up to 125 cm/sec. It handles labels up to 170, 220 or 270mm wide and will wind a roll of labels up to a 300 mm diameter. This model includes durable “Quick-Chuck” quick-locking Core Chuck, permitting the fastest loading and unloading of cores and label rolls. Standard Quick-Chuck: Core diameter: 76mm / Label width: 170mm. Rugged, heavy-gauge steel construction allows your UCAT-3-CHUCK Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving.. Size: W x D x H: 300 x 455 x 320 mm.  LMU009 info pdf pdf ver  1 unid. = 677,00 832,71
UCAT-3-10-INCHES Handles labels up to 255mm wide. Roll diameter capacity up to 300mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. This powered Unwinder, with Tension Arm, automatically tracks label usage and provides powered label feed at speeds up to 125 cm/sec. The UCAT-3-10-INCHES handles labels up to 255mm (10-inches) wide and will unwind a roll of labels up to a 300 mm diameter. LABELMATE’s renowned Constant Adjustable Torque control system allows precise adjustment of feed speeds and rewind torque. External STOP / RUN Input included. Size: W x D x H: 300 x 350 x 320 mm. LMU010 info pdf pdf ver  1 unid. = 577,00 709,71
UCAT-3-CHUCK Handles labels up to 170mm, 220mm or 270mm wide. Roll diameter capacity up to 400mm. Available for 38, 40, 44, 70, 76 and 100mm cores. Speed up to 125cm/sec. This powered Unwinder with Tension Arm automatically tracks label usage and provides powered label feed at speeds up to 125 cm/sec. This model includes durable “Quick-Chuck” quick-locking Core Chuck, permitting the fastest loading and unloading of cores and label rolls. Standard Quick-Chuck: Core diameter: 76mm / Label width: 170mm. Rugged, heavy-gauge steel construction allows your UCAT-40 Unwinder to be simply set in place. Special anti-slip feet keep the unit from moving.. Size: W x D x H: 300 x 385 x 320 mm. LMU012 info pdf pdf ver  1 unid. = 716,00 880,68
220-240V-50HZ PWR SUPPLY MC ACCS MC PL EU PLUG WITH REWINDER  LMX060  1 unid. = 31,00 38,13
PS-MC-UK 220-240V 50HZ UK PLUG ACCS PWR SUPPLY FOR MC AND MC+  LMX061  1 unid. = 31,00 38,13
BAIL STD FOR MC-10 CPNT FOR REWIND NO SHAFT NO CORE  LMX162  1 unid. = 23,00 28,29
TAKE-UP SHAFT LD 200 PRNT  IN LMX337  1 unid. = 40,00 49,20
DISC FOR TAKE UP SHAFT LD CPNT  LMX338  1 unid. = 24,00 29,52
BAIL 100 SPARE PART FOR LD100-UPRNT  IN LMX347  1 unid. = 24,00 29,52
BAIL LD 200 CPNT  LMX350  1 unid. = 24,00 29,52
RING ALU ID 10MM SPARE PART PRNT FOR LD100-U IN LMX358  1 unid. = 20,00 24,60
RING ERTACETAL ID 38MM PRNT SPARE PART FOR LD100-U IN LMX359  1 unid. = 21,00 25,83
DIAMETER EXTENSION CPNT  LMX366  1 unid. = 34,00 41,82
CAP RED BAIL SPARE PART PRNT FOR LD100-U IN LMX372  1 unid. = 19,00 23,37
VANE TAKE-UP 100 SPARE PART PRNT FOR LD100-U IN LMX373  1 unid. = 22,00 27,06
VANE FOR TAKE UP SHAFT LD-200 CPNT  LMX374  1 unid. = 24,00 29,52
EXTERNAL FLANGE MC-10 FOR MC-10 ONLY CPNT 220mm LMX440  1 unid. = 37,00 45,51
APG-MC PAPER GUIDE FOR MC-11 CPNT ADJUSTABLE OUTER EDGE OF LABEL  LMX441  1 unid. = 39,00 47,97
STANDARD SHAFT MC FOR MC WITH VANECPNT BAIL AND INTERNAL FLANGE LMX442  1 unid. = 57,00 70,11
PAPER GUIDE CAT-3(-TA)-ACH CPNT CAT-3(-TA)-CHUCK ADJUSTABLE  LMX444  1 unid. = 40,00 49,20
LD-AWB ADJ WEARLESS BRAKE CPNT 265 ROLL/DIAM 76mmM STD  LMX447  1 unid. = 77,00 94,71
LD-FLANGES-220 INNER&OUTER FLANGE FOR LBL DISPCPNT FITS ALL NOT COMPAT WITH LD-AWB LMX448  1 unid. = 36,00 44,28
LD-FLANGES-300 INNER&OUTER FLANGE FOR LBL DISPCPNT FITS ALL TO BE USED WITH LD-DE  LMX449  1 unid. = 47,00 57,81
EXT COMMAND FACT INSTALLED CONTCPNT CLOSURE ONLY FOR LD-RS/LD-U MOD  LMX450  1 unid. = 77,00 94,71
1 INCH CORE HOLDER 25 4MM CPNT STD SHAFT 155 MM WIDTH 2 FLANGES  LMX460  1 unid. = 69,00 84,87
STANDARD CORE HOLDER SHAFT CPNT WITH VANES AND FLANGES W/155  LMX461  1 unid. = 69,00 84,87
10-INCHES CORE HOLDER Shaft with vanes in 255mm lenght. Specify 38, 40, 44, 70, 46 or 100 mm. 255mm width. 2 flanges LMX462 info  1 unid. = 124,00 152,52
ACH-TWIN Adjustable core holder shaft for cores from 25mm to 101mm, 155mm width, 1 flange LMX463 info  1 unid. = 143,00 175,89
INSP-1 BI DIRECTIONAL VAR SPEEDACCS FOOT SWITCH TWO ROLLERS  LMX470  1 unid. = 115,00 141,45
INSP-1 +PC-1 OPT PRESET COUNTERACCS WITH ADJUSTABLE SENSITIVITY  LMX471  1 unid. = 364,00 447,72
FOOT SWITCH START/STOP ACCS TWIN-CAT-2 UCAT-3 MC REWINDER  LMX472  1 unid. = 77,00 94,71
QUICK-CHUCKS C-76160, diameter 76 mm, width 170 mm LMX483 info pdf  1 unid. = 187,00 230,01
FLANGE-CAT-INT CPNT FOR UCAT-1 º 3 STD º 10-INCHES  LMX489  1 unid. = 37,00 45,51
EXTR FLANGE FOR CAT(TA) CPNT STD&10INCH DIAM 300 MM  LMX490  1 unid. = 40,00 49,20
VANES 40 SET OF 3 VANES CAT-3 CPNT FOR 40 MM CORES  LMX494  1 unid. = 27,00 33,21
VANES 44 SET OF 3 VANES FINS CPNT FOR 44 MM CORES  LMX495  1 unid. = 28,00 34,44
VANES76 CPNT SET OF 3 UNITS FOR 76MM CORES  LMX498  1 unid. = 26,00 31,98
ADJUSTABLE CORE HOLDER ACCS 25TO101MM DIAMETER INNER FLANGE  LMX500  1 unid. = 111,00 136,53
BAIL-CAT-ST CPNT FOR REWIND ON SHAFT FOR CAT 3  LMX501  1 unid. = 28,00 34,44
QUICK-CHUCKS OPTIONAL FLANGE 300mm outer Flange for QC 76 mm core diameter. LMX508 info  1 unid. = 49,00 60,27
QUICK-CHUCKS OPTIONAL FLANGE 400mm outer Flange for QC 76 mm core diameter. LMX511 info  1 unid. = 72,00 88,56
BH-1 ADDITIONAL BLADE HOLDER ASEMBLYCPNT PRECISION HIGH-SPEED BLADE  LMX515  1 unid. = 40,00 49,20
HSB-10 10 PRECISION HIGH-SPEED BLADES ACCS FOR SLITTERS  LMX516  1 unid. = 28,00 34,44
SP-40-220 LABEL SEPARATOR PLATES ACCS 220mm DIAMETER FOR 40MM PLASTIC  LMX523  1 unid. = 27,00 33,21
LABELSEPARATORPLATES SP-76-220 ACCS 220MM DIAMETER FOR 76MM  LMX529  1 unid. = 31,00 38,13
LABELSEPARATORPLATES F/ SLITTERACCS 220MM DIAMETER FOR 76MM CORES  LMX530  1 unid. = 27,00 33,21
LABELSEPARATORPLATES F/ SLITTERACCS 300MM DIAMETER FOR 76MM CORES  LMX531  1 unid. = 36,00 44,28
PS-15V-3A CPNT  LMX537  1 unid. = 48,00 59,04
Quando indicada uma "Quantidade mínima sugerida" o preço refere-se ao total dessa quantidade, pode vender-se só 1, mas em quantidade é mais barato, para outras quantidades consulte-nos           _______    

Outros modelos ou atualizações:
Por favor consulte
Bookmark and Share

Ver taxas lei da cópia privada